Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

24 VDC 线圈带ISO/DIN 43650, Form A接头带TVS二极管

全部展开

技术特性 [ + ]

线圈绕组采用温度等级N, (392° F [200 °C]等级)。
直流线圈内嵌入瞬态电压抑制二极管。名义击穿电压68V。代码1.5 KE68CA。75℃下稳态电源损耗6.5W，峰值脉冲损耗为1ms时1500W，不可重复。
带插头的电源线缆需要单独配置，未包含在产品里面。
线圈电磁对称，可以双向安装到螺线管上，不影响使用性能。
为了得到最优的比例性能，应当使用带有电流反馈和可调颤振信号的放大器。颤振频率应当设置为100 - 250 Hz。
该线圈符合CE认证。符合低电压指令 (2006/95/EC) 和EN 60204-1:2006。
IP等级取决于线圈插座类型以及与之相配的插头。
RoHS认证，限制性材料重量占比低于0.1%。
外部金属壳体重铬酸盐镀锌。

回到首页

比例性能数据 [ + ]

最大电流	590 mA590 mA
122ºF (50ºC)稳定温度下名义线圈电阻	37.2 ±5% ohms37.2 ±5% ohms
Nominal Coil Resistance at 68ºF (20ºC) Cold	26.2 ±5% ohms26.2 ±5% ohms

回到首页

技术数据 [ + ]

在 68ºF (20ºC) 环境温度下，线圈最高温度	218ºF (105ºC)218ºF (105ºC)
电弧消除(TVS)	IncludedIncluded
电量消耗（低温）- 在相关的电压下	22 watts22 watts
最高环境温度	122 °F50 °C
电压/频率	24 VDC24 VDC
运行电压范围	+/- 10% nominal+/- 10% nominal
寿命测试等级	100 %100 %
接头	ISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pinISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pin
接头防护等级	IP65/IP67IP65/IP67
衔铁直径	.75 in.19 mm
线圈锁紧螺母扭矩	4.5 lbf in.0,5 Nm
型号重量	8.2 oz.8.2 oz.