2通, 电磁锥阀换向阀 - 在单向阀后

流量: 10 gpm40 L/min. | 插孔: T-11A

全部展开

技术特性 [ + ]

此类在单向阀后的电磁阀为一个组合阀。它利用直动式，锥阀结构电磁阀置于单向阀后面组合成一个三通路。单向阀的自由流方向为从进口（口2）到系统口（口1）。当电磁阀失电，口2到口3是不通的。此种组合阀常用于升/降应用中并可直接集成到驱动器上。

电磁铁组件的疲劳耐压等级为5000 psi (350 bar)。
此阀有几种不同的手动紧急操作选项，包括无手动紧急操作。见以下可选选项。请注意：风雨线圈不兼容手动紧急操作功能。
适合负载锁紧回路。
带D或L控制的型号，手动重载中的止动机构是用来作临时驱动用途。
此阀采用湿式衔铁线圈设计。这意味着衔铁周围的工作流体介质将曝露在线圈所产生热场中。如果线圈长时间通电，这将是一个影响因素。一些液体，特别是水/乙二醇混合物，会在长时间高温下分解并形成凡立水，而这将会影响阀的功能。
线圈可以和Sun的系列1电磁阀产品互换并可从另外一个方向上安装在套筒上。
线圈接头等级可提供至IP69K。请见单个线圈产品的详细产品说明。额外的风雨线圈和工具包可提供更完善的环境防护。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-11A
系列	1
通流能力	10 gpm40 L/min.
最大操作压力	5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏	10 drops/min.@5000 psi0,7 cc/min.@350 bar
单向开启压力	30 psi2 bar
手动紧急操作需要的力	5 lbs/1000 psi @ Port 133 N/100 bar @ Port 1
手动紧急操作动作行程	.10 in.2,5 mm
额定响应时间	50 ms50 ms
切换频率	15,000 max. cycles/hr15,000 max. cycles/hr
衔铁直径	.75 in.19 mm
阀头部安装六角尺寸	7/8 in.22,2 mm
阀安装扭矩	30 - 35 lbf ft41 - 47 Nm
Seal and nut kit - Coil	Viton: 990770006
Seal kit - Cartridge	Buna: 990011007
Seal kit - Cartridge	Polyurethane: 990011002
Seal kit - Cartridge	Viton: 990011006

回到首页

性能曲线 [ + ]

Performance Curve for HDDA: 2通, 电磁锥阀换向阀 - 在单向阀后

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting, pilot operated, what do I use?

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

Where would I use a DR__ instead of a DP__?

In many circuits the directional cartridge is set to shift at a low pressure no matter how high the pilot pressure goes. If you use a DP__ , the pilot flow increases to significant amounts. A DR__ however will only consume a small amount of flow. A DP__ is useful when you want to block or open the pilot flow to shift the valve.

回到首页

Related Models [ + ]