Assembly Build Process

X
?

Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

✕

740系列, 28 VDC, 高功率线圈带Metri-Pack系列 150-2M接头适配器不带TVS二极管

740828 : 740系列, 28 VDC, 高功率线圈带Metri-Pack系列 150-2M接头适配器不带TVS二极管

技术特性 [ + ]

This 740 Series Coil configuration uses a connector adapter kit to provide the required termination.

Model code 740828 includes coil 740928 and adapter cable 991717.
线圈绕组采用N级(392° F [200 °C]等级) 电磁线。
需要配对的电源线缆，该线缆并没有包含在线圈里。
该线圈电磁力匀称，可以在线圈上任意方向安装以方便接线，对性能无任何影响。
线圈完全符合RoHS要求，受限制的材料重量比小于0.1%。
外部的金属壳为锌镍镀层，提供1000小时的盐雾保护。
为了优化比例性能，应当使用带有电流反馈和可调颤振的放大器。颤振频率调节范围100-250Hz。
该线圈内没有瞬态电压抑制二极管（TVS），当存在其他浪涌电压抑制电子元件时才推荐使用。若没有其他浪涌电压抑制电子元件，应当使用内置瞬态电压抑制二极管（TVS）的线圈。
工艺性能为IPC-A-620，2级。
U黑色L 3289CSA 18测量线。
This coil is CE compliant. It meets the requirements of the Low Voltage Directive (2006/95/EC) and EN 60204-1:2006.

比例性能数据 [ + ]

最大电流 - FLeX阀(最高环境温度且100%工作时间下)	500 mA500 mA
最大电流 - 非FLeX阀(最高环境温度且100%工作时间下)	560 mA560 mA

技术数据 [ + ]

运行温度范围	-40 to 230 °F-40 to 110 °C
电弧消除(TVS)	NoneNone
电量消耗（低温）- 在相关的电压下	25 Watts25 Watts
最高环境温度	122 °F50 °C
电压/频率	28 VDC28 VDC
运行电压范围	+10%/-15%+10%/-15%
寿命测试等级	100 %100 %
接头	Metripack Series 150-2MMetripack Series 150-2M
衔铁直径	.62 in.15,7 mm
线圈锁紧螺母扭矩	4.5 lbf in.0,5 Nm
型号重量	9.6 oz.272 grams

常见问题 [ + ]

What are the shock and vibration levels the 740 coils are capable of withstanding?

740 Series coils meet Sun specification S-367. This specification is on our website under Technical Resources and is also listed in the Additional Resources tab on applicable product pages. Please see sections 11 and 12 of Environmental Test Specification for Electrical and Electronic Components; S-367.

适用于 [ + ]

What models can this kit be used with?

DBAF 3通电磁滑阀换向阀 - 先导流量 (740系列)
DFBF FLeX系列 2通, 2级, 电磁锥阀换向阀带反向单向阀 - 流量 2到1
DFBG FLeX系列 2通, 2级, 电磁锥阀换向阀带反向单向阀 - 流量 2到1
DFCI 2通, 2级, 电磁锥阀换向阀 - 流量 1到2 (740系列)
DFCJ 2通, 2级, 电磁锥阀换向阀 - 流量 2到1 (740系列)
DFDI 2通, 2级, 电磁锥阀换向阀 - 流量 1到2 (740系列)
DFDJ 2通, 2级, 电磁锥阀换向阀 - 流量 2到1 (740系列)
DFEI 2通, 2级, 电磁锥阀换向阀 - 流量 1到2 (740系列)
DFEJ 2通, 2级, 电磁锥阀换向阀 - 流量 2到1 (740系列)
DFFI 2通, 2级, 电磁锥阀换向阀 - 流量 1到2 (740系列)
DFFJ 2通, 2级, 电磁锥阀换向阀 - 流量 2到1 (740系列)
DLDF 2通, 电磁滑阀换向阀 (740系列)
DLDFS 2通, 软切换, 电磁滑阀换向阀 (740系列)
DMBF FLeX系列 3通, 电磁滑阀换向阀
DTAF FLeX系列 2通, 直动式, 电磁锥阀换向阀
DTAFS FLeX系列 2通, 软切换, 电磁锥阀换向阀 - 先导流量
DTBF FLeX系列 2通, 直动式, 电磁锥阀换向阀
DTCF 2通, 直动式, 电磁锥阀换向阀带遮盖 (740系列)
DTDF 2通, 直动式, 电磁锥阀换向阀 (740系列)
DTDFS 2通, 直动式, 软切换, 电磁锥阀换向阀 (740系列)
DWBF FLeX系列 3通, 直动式, 电磁锥阀换向阀
DWDF 3通, 直动式, 电磁锥阀换向阀 (740系列)
FDEP 2通, 直动式电比例, 压力补偿流量控制阀带反向单向阀
FMDF 电比例 3通流量控制阀, 进口节流 (740系列)
FMDG 电比例 3通流量控制阀, 进口节流 (740系列)
FPBF FLeX系列先导式, 常闭, 电比例节流阀 - 流量 2到1
FPBG FLeX系列先导式, 常闭, 电比例节流阀带反向单向阀 - 流量 2到1
FPBI FLeX系列先导式, 常开, 电比例节流阀 - 流量 2到1
FPBJ FLeX系列先导式, 常开, 电比例节流阀带反向单向阀 - 流量 2到1
FPBU FLeX系列电比例, 锥阀节流阀 - 常闭
FREP FLeX系列 3通, 直动式, 电比例, 旁路/节流, 优先流量控制阀
PRDF 电比例, 直动式, 减压/溢流阀带开式过渡位 (740系列)
PRDG 电比例, 直动式, 减压/溢流阀 (740系列)
RPEI 电比例溢流阀 - 无命令时最高压力设定
RVCK FLeX系列 2级, 电磁操作可调式溢流阀, 常泄
RVCL FLeX系列 2级, 电磁操作可调式溢流阀, 通电泄油
RVCM FLeX系列 2级, 电磁操作可调式溢流阀, 通电关闭
RVCN FLeX系列 2级, 电磁操作可调式溢流阀, 常闭

额外来源 [ + ]

集锦

技术指导

电磁换向阀/比例换向阀的电磁线圈 (609.43 KB)

技术信息

740 Series Coils - Derating Tables (56.42 KB)
Environmental Test Specification for Electrical and Electronic Co (254.61 KB)
Sun的浮动式螺纹插装阀 (710.21 KB)
推荐液压油及工作温度
CE Declaration of Conformity - XMD 12-2017 (133.69 KB)
XMD Coil Clip Installation Guide (749.23 KB)