DTAFS | 插装阀 » Directional » 2-通

这款FLeX系列2位2通电磁阀为直动式，锥阀结构，带有软切换功能。有常开或者常关配置选项。该阀使用力平衡设计，具有低泄漏量，可以在双向允许或者阻止油液流动。该阀可以直接安装在顶部自带插孔的一系列SUN先导控制或外接控制阀上，实现集成先导控制。

软切换阀与标准阀可替换，但是流通能力降低。
软切换特性可极大地减少阀驱动时候带来的冲击，但是不宜用在计时很关键的应用中。如果需要精确的斜坡上升或计时控制，请考虑使用Sun的电比例阀。
此软切换特性将比Sun的标准电磁阀显著增加响应时间。响应时间取决于流量，压力，线圈电压，油液粘度和周围的温度。典型响应时间范围为150ms到300ms。
为了获得一致的软切换特性，口1应该有正压力。
此阀可被直接安装进Sun先导控制和外接口控制阀中以提供电磁先导控制功能。单独的先导油路被去除，只需要加工一个插孔来整合先导控制级和主级的功能。
适合负载锁紧回路。
设计以及测试通过1000万次开关工作循环。
疲劳以及爆破压力等级符合新的NFPA测试标准T2.6.1 R2014。
相近的尺寸下拥有比竞争对手更高的通流能力。
使用CFD流体仿真软件进行几何形状优化设计。
该类阀的所有配置均配备锌-镍镀层，能够提供1000小时盐雾保护。
常闭式选项可以使用FLeX低功率，高功率或者防爆线圈。常开式选项仅可以使用FLeX高功率或者防爆线圈。
线圈插头提供最高IP69K防护等级，详细信息见线圈产品页。
该阀提供推式手动应急选项。
该阀具有极低的泄漏量 - 0.004 in³ (0.07 cc³)/min (1 滴/min)。
详细产品页面在该网页上部可以下载浏览。
不同的线圈接头与电压选项都是可选的，也同时可选带或不带浪涌保护。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-8A
系列	P
通流能力	7 gpm28 L/min.
最大操作压力	5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏	0.004 in³/min.@5000 psi0,07 cc/min.@350 bar
手动紧急操作需要的力	10 lbs/1000 psi @ Port 166 N/100 bar @ Port 1
粘度范围	35 - 2000 SUS2,8 - 380 cSt
阀头部安装六角尺寸	3/4 in.19,1 mm
阀安装扭矩	20 - 25 lbf ft27 - 33 Nm
型号重量	.40 lb0,20 kg
美国专利号#	10,302,20110,302,201
Seal and nut kit - Coil	Viton: 990740006
Seal kit - Cartridge	Buna: 990608007
Seal kit - Cartridge	Viton: 990608006

回到首页

Performance Curve for DTAFS: FLeX系列 2通, 软切换, 电磁锥阀换向阀 - 先导流量

回到首页

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting, pilot operated, what do I use?

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What is the difference between nominal and maximum flow capacity?

Nominal flow capacity is based on performance limits. Maximum flow capacity is based on pressure drop. When selecting any direct-acting solenoid valve, first check the performance limits plot, then check if pressure drop is acceptable.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

Where would I use a DR__ instead of a DP__?

In many circuits the directional cartridge is set to shift at a low pressure no matter how high the pilot pressure goes. If you use a DP__ , the pilot flow increases to significant amounts. A DR__ however will only consume a small amount of flow. A DP__ is useful when you want to block or open the pilot flow to shift the valve.

Is the FLeX program available in QuickDesign SmartConnect?

Yes. All FLeX phase 1 valves are available in the SmartConnect schematic tool, and are also available for submittal to QuickDesign.

Do FLeX valves utilize a floating nose design?

Yes. All FLeX valves utilize the Sun floating nose design.

回到首页