Triple 溢流 selector 安装组件
Function
![Function for YRDC: YRDC](https://cmsimages.sunhydraulics.com/sym_YRDC.png)
YRDC
Port Designators [ + ]
Modifiers | Ports |
J | Ports P & T: SAE 8; Gage Port: SAE 6; |
V | Ports P & T: 1/2" BSPP; Gage Port: 1/4" BSPP; |
技术特性 [ + ]
先导控制式,平衡滑阀结构溢流阀为常闭压力调节阀。当进口(口P)压力达到阀设定值,阀开始向油箱(口T)溢流,节流以调节压力。此类阀压力调节精度高,压力波动随流量变化小,并且调节平稳,噪声小,响应速度适中。此装配体包含3个溢流阀,允许选择3种单独的溢流设置,并附加所有口全部堵塞的功能。
- 因为滑阀的泄漏,不适合使用在负载锁紧应用中。
- 油箱口(口2)处的背压直接以1:1的比例增加到阀的设定值上。
- 利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。
技术数据 [ + ]
阀块类型 | 管式安装管式安装 |
通流能力 | 25 gpm95 L/min. |
安装孔直径 | .28 in.7,1 mm |
安装孔深度 | ThroughThrough |
安装孔数量 | 33 |
常见问题 [ + ]
There are exactly 250 Sun drops in a cubic inch or 15 in a cc.
Reasons to anodize:
- To increase corrosion resistance. Sun uses 6061-T651 aluminum. It is one of the most corrosion resistant aluminum alloys there is. Whether or not anodizing improves the corrosion resistance of 6061 aluminum is debatable. We have yet to have a manifold returned because of corrosion.
- Appearance (color). The 2 colors that would appeal to Sun would be blue or black. Unfortunately these are the colors that are hardest to do consistently.
- To provide a hard wear surface. Sun does not make parts-in-body valves. The manifold is just plumbing. We don't need a wear surface.
- Because everyone else does it. Bad reason.
Reasons to not anodize:
- Cost. It's another process.
- Logistics. When you make tens of thousands of manifolds a month and you anodize hundreds, it's a problem. Consistency. See above.
- Stamping. After a body is anodized you cannot do any more stamping without making a mess.
Inspection. Have you ever tried to look for burrs in a black anodized body? It's the old blackboard factory at night scenario. - Torque. You will experience an increase in breakaway torque when removing items from an anodized manifold.
- Fatigue life. This is the best reason to not anodize. Fatigue failure is a very complex phenomenon. What it takes to initiate a crack is difficult to predict. What it takes to propagate a crack is readily defined. Anodizing produces a very thin, very hard, and very brittle surface on aluminum. The first time you pressurize an anodized aluminum manifold you have initiated fatigue cracks. Whether or not the stress is enough to propagate the cracks is a matter of pressure and manifold geometry. Anodizing an aluminum manifold grossly reduces the fatigue life by anywhere from 20% to 50%.
Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.
备注 [ + ]
- Number at spool indicator arrow corresponds to selected relief valve. The (X) position (opposite position) is the all-ports blocked position.
- All handle positions are detented.
- Handle & stops may be changed to limit valve to 2, 3, or 4 position use.
- Important: Carefully consider the maximum system pressure. The pressure rating of the manifold is dependent on the manifold material, with the port type/size a secondary consideration. Manifolds constructed of aluminum are not rated for pressures higher than 3000 psi (210 bar), regardless of the port type/size specified.
- For detailed information regarding the cartridges contained in this assembly, click on the models codes shown in the Included Components tab.
额外来源 [ + ]