电比例 3通 流量控制阀, 进口节流
此阀是一个3通,进口节流,电比例节流阀。电磁线圈失电时,油路为供油口1口不通,口2通过口3处的油箱泄油。线圈得电时,在口1到口2方向上此阀将形成一个与电流大小成比例的节流口。此阀在口1到口2方向上具有自补偿效果,当接入外部压力补偿器时,此阀可提供压力补偿流量控制。口2到口3方向的流量不成比例。
- 换向过程中工作口相互不通。
- 可以使用2个3通的阀来实现4通的功能。
- 这些阀或许需要通过外部调节逻辑阀提供压力补偿。对并联回路采用LR*C-XHN,或者对于节流回路采用LP*C-XHN。
- 这款阀提供一定程度的自我补偿,可以用于流量控制。为提高流量控制的精准度,外部的逻辑调节阀可以用来保证大范围流量和压力情况下稳定的流量。可参考附加信息中的曲线。
- 所有口耐压为5000psi(350bar)
- 线圈可与SUN其他电磁流量阀互换,同时它可以以任意方向安装。
- 未获得最好性能,需要使用带有颤振信号的电流式放大器。颤振信号调节范围为100-250Hz。
- 在使用“D”或“L”控制的方式中,这种人工的制动装置只是应用于紧急制动。这种“D”、"E"、“L”或“T”型的人工控制装置大约有7000次的机械寿命。
- 瞬时/旋转重载选项“E”允许操作者顺时针旋转手动重载装置90度以切换阀。
- Sun浮动式的结构可以最大限度地减少由于过大的安装扭矩以及孔型加工的误差所造成的干涉现象
滞环(在颤振作用下) | <4%<4% |
直流驱动下滞环 | <8%<8% |
线性度(在颤振作用下) | <2%<2% |
重复精度(带颤振) | <2%<2% |
推荐颤振频率 | 140 Hz140 Hz |
名义死区(一定的输出) | 60%60% |
插孔 | T-11A |
系列 | 1 |
通流能力 | 6 gpm23 L/min. |
110 SUS (24 cSt)下的最大泄漏 | 2 in³/min.@1000 psi30 cc/min.@70 bar |
手动紧急操作需要的力 | 5 lbs/1000 psi @ Port 133 N/100 bar @ Port 1 |
手动紧急操作动作行程 | .10 in.2,5 mm |
衔铁直径 | .75 in.19 mm |
阀头部安装六角尺寸 | 7/8 in.22,2 mm |
阀安装扭矩 | 30 - 35 lbf ft41 - 47 Nm |
型号重量(带线圈) | 1.10 lb0,50 kg |
Seal and nut kit - Coil | Viton: 990770006 |
Seal kit - Cartridge | Buna: 990411007 |
Seal kit - Cartridge | Viton: 990411006 |
We claim +/- 10%. We set to +/- 5% in production testing to allow for differences in customers' conditions. If you want accuracy, stay in the bottom 2/3rds of the range. Our 12 gpm (45 L/min.) flow controls are quite flat at 9 gpm (34 L/min.) and dead flat below 6 gpm (23 L/min.), until you get to the bottom of the range. Below about .25 gpm (1 L/min.), spool leakage and orifice conditions start to limit accuracy.
I am afraid not. Unless you are overflowing your current valve and correctly size ours, you are not likely to notice any improvement. Priority flow controls are not efficient devices. They are an easy way to get more than 1 source of oil from 1 pump but they can generate a lot of heat. Try to size your actuators so the pressures are similar on both the priority and the bypass circuits. If you can't do that, try to have the lower flow leg be the lower pressure. The pump pressure is determined by whichever leg is higher and if there is flow that is taking a pressure drop that is not doing work it is creating heat.
All flow is blocked, hence the term priority. The priority flow has to be satisfied.
The valve acts as a 2 port restrictive flow control.
The spring force in our flow controls equates to about 100 psi (7 bar). This is high enough to give the valves acceptable capacity and not too high for proper circuit operation. 100 psi (7 bar) is the spring force; at the upper end of the flow control's range, the drop through the valve will be as high as 250 psi (17 bar) before it starts modulating.
There are exactly 250 Sun drops in a cubic inch or 15 in a cc.
In a meter-in flow control circuit if the pump is set at 3000 psi and the load is 2000 psi the drop through the flow control is 1000 psi. In a meter-out circuit with the load at 2000 psi the drop through the flow control is 2000 psi.
- 当选择Sun阀块时,请检查插装阀的间隙要求。不同的阀控制方式以及线圈要求的间隙不一样。
- Electro-Proportional Basics Explained
- 插孔节省™复合功能阀 简化你的液压方案
- Sun Cartridges with EPDM Seals
- Check Valves, Flow Control and Priority Flow Control Valves Technical Tips
- CANpoint XMD 编程软件
- FleX系列电磁操纵阀新产品 ——让客户有更多选择
- 大流量电液比例节流阀
- Another Optimized Solution from Sun Hydraulics!
- QuickDesign with SmartConnect Offers Drag-and-Drop Schematic Tool
- Sun推出抗腐蚀产品解决方案
- Sun's Proportional Valves Enable Meter-in and Meter-out in Motion Control Circuits
- 经过原厂设定的电液控制方案,开箱即用
- Sun FLeX™系列电磁阀&线圈
- Weatherized Solenoid Valves for Harsh Environments
- 使用AmpSet Blue™来设置您的内置蓝牙式放大器
- Sun’s Cartridge Symbol Library
- Technical Tips for Proportional Amplifiers and Ancillary Products (2.4 MB(兆))
- Sun插装阀插孔 (551.8 KB)
- 电磁换向阀/比例换向阀的电磁线圈 (609.43 KB)
- 电比例插装阀 (1.47 MB(兆))
- Electro-Proportional Cartridge Valves (1.28 MB(兆))
- 计量,设定的单位及换算
- Sun 产品编码; 999-901-334-ZH (582.27 KB)
- Electro-Hydraulic Terms and Definitions (2.94 MB(兆))
- 性能数据
- 插装阀:结构材料
- Cavity Information (S-171) and Tooling
- Sun的浮动式螺纹插装阀 (710.21 KB)
- 推荐液压油及工作温度
No coil selected.