Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

12 VDC 线圈带双出线不带TVS二极管

全部展开

技术特性 [ + ]

This DC coil does not include a TVS surge suppression diode. Coils without TVS diodes should only be used when surge suppression is included elsewhere in the electrical system.
The coil is magnetically symmetrical and can be mounted in either direction on the solenoid tube without affecting performance.
For optimum proportional performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between 100 - 250 Hz.
Coil windings utilize Class N, (392° F [200 °C] rated) magnet wire.
外部金属壳体经过三价光亮镀锌处理。
IP rating is dependent on the coil connector and the mating connector used.
RoHS compliant. Restricted materials less than 0.1% total by weight.

回到首页

比例性能数据 [ + ]

最大电流	1150 mA1150 mA
122ºF (50ºC)稳定温度下名义线圈电阻	9.4 ±8% ohms9.4 ±8% ohms
Nominal Coil Resistance at 68ºF (20ºC) Cold	6.4 ±8% ohms6.4 ±8% ohms

回到首页

技术数据 [ + ]

在 68ºF (20ºC) 环境温度下，线圈最高温度	218ºF (105ºC)218ºF (105ºC)
电弧消除(TVS)	NoneNone
电量消耗（低温）- 在相关的电压下	22 watts22 watts
电压/频率	12 VDC12 VDC
运行电压范围	+/- 10% nominal+/- 10% nominal
寿命测试等级	100 %100 %
接头	Twin lead 18 AWG x 18 in. (460 mm)Twin lead 18 AWG x 18 in. (460 mm)
接头防护等级	IP65IP65
衔铁直径	.75 in.19 mm
线圈锁紧螺母扭矩	4.5 lbf in.0,5 Nm