Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

740系列, 24 VDC, 低功率线圈带Metri-Pack系列 150-2M接头适配器和TVS二极管

全部展开

技术特性 [ + ]

This 740 Series Coil configuration uses a connector adapter kit to provide the required termination.

Model code 740824LD includes coil 740924LD and adapter cable 991717.
线圈绕组采用N级(392° F [200 °C]等级) 电磁线。
需要配对的电源线缆，该线缆并没有包含在线圈里。
该线圈电磁力匀称，可以在线圈上任意方向安装以方便接线，对性能无任何影响。
线圈完全符合RoHS要求，受限制的材料重量比小于0.1%。
外部的金属壳为锌镍镀层，提供1000小时的盐雾保护。
线圈内置瞬态电压抑制二极管（TVS）。
为了优化比例性能，应当使用带有电流反馈和可调颤振的放大器。颤振频率调节范围100-250Hz。
工艺性能为IPC-A-620，2级。
U黑色L 3289CSA 18测量线。
This coil is CE compliant. It meets the requirements of the Low Voltage Directive (2006/95/EC) and EN 60204-1:2006.

回到首页

比例性能数据 [ + ]

最大电流 - FLeX阀(最高环境温度且100%工作时间下)

420 mA420 mA

回到首页

技术数据 [ + ]

运行温度范围	-40 to 230 °F-40 to 110 °C
电弧消除(TVS)	IncludedIncluded
电量消耗（低温）- 在相关的电压下	17 Watts17 Watts
最高环境温度	212 °F100 °C
20º C下电阻	33.9 ohms ±10%33.9 ohms ±10%
TVS二极管 (名义) 击穿电压	68 VDC68 VDC
电压/频率	24 VDC24 VDC
运行电压范围	+10%/-15%+10%/-15%
寿命测试等级	100 %100 %
接头	Metripack Series 150-2MMetripack Series 150-2M
衔铁直径	.62 in.15,7 mm
线圈锁紧螺母扭矩	4.5 lbf in.0,5 Nm
型号重量	6.4 oz.181 grams

回到首页

常见问题 [ + ]

What are the shock and vibration levels the 740 coils are capable of withstanding?

740 Series coils meet Sun specification S-367. This specification is on our website under Technical Resources and is also listed in the Additional Resources tab on applicable product pages. Please see sections 11 and 12 of Environmental Test Specification for Electrical and Electronic Components; S-367.

回到首页

适用于 [ + ]

What models can this kit be used with?