Caudal libre de nariz al lado anti-retorno válvula

Capacidad: 40 gpm160 L/min. | Cavidad: T-5A
Technical Features [ + ]

Free-flow, nose-to-side check valves are on/off circuit components that allow free flow from the inlet (port 1) to the outlet (port 2) and block flow in the opposite direction.

  • Two-port check valves share the same cavity for a given frame size, however, pay close attention as flow paths may be in opposite directions.
  • Check valves offer extremely low leakage rates with a maximum leakage of less than 1 drop per minute (0,07 cc/min).
  • Will accept 5000 psi (350 bar) at ports 1 and 2.
  • Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
  • Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP or /LH (see CONFIGURATION section). For further details, please see the Materials of Construction page.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
Back to Top
Technical Data [ + ]
Notar: Los datos pueden variar según la configuración . Consulte la sección de CONFIGURATION
cavidad T-5A
Series 2
Capacity 40 gpm160 L/min.
Maximum Operating Pressure 5000 psi350 bar
Maximum Valve Leakage at 110 SUS (24 cSt) 1 drops/min.0,07 cc/min.
Valve Hex Size 1 1/8 in.28,6 mm
Valve Installation Torque 45 - 50 lbf ft61 - 68 Nm
Model Weight .40 lb0,20 kg
Seal kit - Cartridge Buna: 990203007
Seal kit - Cartridge EPDM: 990203014
Seal kit - Cartridge Viton: 990203006
Back to Top
Performance Curves [ + ]
Performance Curve for CXFA: Caudal libre de nariz al lado anti-retorno válvula Performance Curve for CXFA: Caudal libre de nariz al lado anti-retorno válvula
Back to Top
FAQs [ + ]
How big is a drop of hydraulic oil?  

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting or pilot operated - what do I use?

Direct-acting valves are used to prevent over pressure, and pilot-operated valves are used to regulate pressure. If you are unsure, use a direct-acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot-operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

I need to discharge a large accumulator. How can I increase the capacity of my discharge circuit?

Because of the very high ratio, the COFO has limited capacity. The discharge path is across a .050 inch (1,3 mm) diameter orifice. If you have large accumulators combined with low precharge pressures, this may not discharge the energy quickly enough. Using the COFO XDN cartridge in conjunction with an LODA XDN will provide capacity for larger applications.

What parts of the Sun cartridge valve are field serviceable?
Only external seals are serviceable.  Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.
Back to Top
  • 3BC Cushion lock with shuttle
  • 3BD Cushion lock with shuttle
  • 3BK Cushion lock with shuttle
  • 3BL Cushion lock with shuttle
  • 3BV Cushion lock with shuttle
  • 3BW Cushion lock with shuttle
  • 4BC Cushion lock with make up checks
  • 4BD Cushion lock with make up checks
  • 4BK Cushion lock with make up checks
  • 4BL Cushion lock with make up checks
  • 4BV Cushion lock with make up checks
  • 4BW Cushion lock with make up checks
  • 5BC Cushion lock with make up checks and shuttle
  • 5BD Cushion lock with make up checks and shuttle
  • 5BK Cushion lock with make up checks and shuttle
  • 5BL Cushion lock with make up checks and shuttle
  • 5BV Cushion lock with make up checks and shuttle
  • 5BW Cushion lock with make up checks and shuttle
  • B6A Ninety degree with reverse flow check - sequence
  • B6B Ninety degree with reverse flow check - sequence
  • B6C Ninety degree with reverse flow check - sequence
  • B6D Ninety degree with reverse flow check - sequence
  • B6I Ninety degree with reverse flow check - sequence
  • B6J Ninety degree with reverse flow check - sequence
  • B6K Ninety degree with reverse flow check - sequence
  • B6U Ninety degree with reverse flow check - sequence
  • B6V Ninety degree with reverse flow check - sequence
  • B6W Ninety degree with reverse flow check - sequence
  • B7B Through port 1 with reverse flow check
  • B7C Through port 1 with reverse flow check
  • B7D Through port 1 with reverse flow check
  • B7J Through port 1 with reverse flow check
  • B7K Through port 1 with reverse flow check
  • B7L Through port 1 with reverse flow check
  • B7U Through port 1 with reverse flow check
  • B7V Through port 1 with reverse flow check
  • B7W Through port 1 with reverse flow check
  • B8B 2 cylinder sequence, with reverse checks
  • B8C 2 cylinder sequence, with reverse checks
  • B8D 2 cylinder sequence, with reverse checks
  • B8J 2 cylinder sequence, with reverse checks
  • B8K 2 cylinder sequence, with reverse checks
  • B8U 2 cylinder sequence, with reverse checks
  • B8V 2 cylinder sequence, with reverse checks
  • B8W 2 cylinder sequence, with reverse checks
  • BB2 ISO 05: Reducer on A with reverse flow check
  • BB3 ISO 05: Reducer on B with reverse flow check
  • BB9 ISO 05: Reducer on A and B with reverse flow check
  • BJ2 ISO 05 - X&Y: Reducer on A with reverse flow check
  • BJ3 ISO 05 - X&Y: Reducer on B with reverse flow check
  • BJ9 ISO 05 - X&Y: Reducer on A and B with reverse flow check
  • BPC Cushion lock with make up checks
  • BPD Cushion lock with make up checks
  • BPK Cushion lock with make up checks
  • BPL Cushion lock with make up checks
  • BPV Cushion lock with make up checks
  • BPW Cushion lock with make up checks
  • BQC Cushion lock with make up checks and shuttle
  • BQD Cushion lock with make up checks and shuttle
  • BQK Cushion lock with make up checks and shuttle
  • BQL Cushion lock with make up checks and shuttle
  • BQV Cushion lock with make up checks and shuttle
  • BQW Cushion lock with make up checks and shuttle
  • CB2 ISO 05: A to T, check T to B
  • CB4 ISO 05: On A with reverse flow check
  • CB5 ISO 05: On B with reverse flow check
  • CJ2 ISO 05 - X&Y: A to T, check T to B
  • CJ4 ISO 05 - X&Y: On A with reverse flow check
  • CJ5 ISO 05 - X&Y: On B with reverse flow check
  • CK3 ISO 07: B to T, check T to A
  • CKJ ISO 07: A to T, check T to B
  • CMB Cross port with make up checks
  • CMC Cross port with make up checks
  • CMD Cross port with make up checks
  • CMJ Cross port with make up checks
  • CMK Cross port with make up checks
  • CML Cross port with make up checks
  • CMU Cross port with make up checks
  • CMV Cross port with make up checks
  • CMW Cross port with make up checks
  • CNB Ninety degree with reverse flow check
  • CNC Ninety degree with reverse flow check
  • CND Ninety degree with reverse flow check
  • CNI Ninety degree with reverse flow check
  • CNJ Ninety degree with reverse flow check
  • CNK Ninety degree with reverse flow check
  • CNU Ninety degree with reverse flow check
  • CNV Ninety degree with reverse flow check
  • CNW Ninety degree with reverse flow check
  • DNB Ninety degree with reverse flow check
  • DNC Ninety degree with reverse flow check
  • DND Ninety degree with reverse flow check
  • DNJ Ninety degree with reverse flow check
  • DNK Ninety degree with reverse flow check
  • DNL Ninety degree with reverse flow check
  • DNU Ninety degree with reverse flow check
  • DNV Ninety degree with reverse flow check
  • DNW Ninety degree with reverse flow check
  • NB2 ISO 05: Reducer/reliever on A with reverse flow check and port 4 external
  • NB3 ISO 05: Reducer/reliever on B with reverse flow check and port 4 external
  • NJ2 ISO 05 - X&Y: Reducer/reliever on A with reverse flow check and port 4 external
  • NJ3 ISO 05 - X&Y: Reducer/reliever on B with reverse flow check and port 4 external
  • U7P ISO 03: On B with free flow check
  • U8B ISO 05 - X&Y: On A with reverse flow check
  • WAT P to T, check on P, side ports
  • WAU P to T, check on P, side ports
  • WAV P to T, check on P, side ports
  • WAW P to T, check on P, side ports
  • WAX P to T, check on P, side ports
  • WAY P to T, check on P, side ports
  • WHY ISO 05 - X&Y: Priority flow control on A with reverse flow check
  • WHZ ISO 05 - X&Y: Priority flow control on B with reverse flow check
  • X9K Danfoss OMS: Cushion lock with make up checks
  • X9N Danfoss OMS: Cushion lock with make up checks
  • X9P Danfoss OMS: Cushion lock with make up checks
  • X9R Danfoss OMS: Cushion lock with make up checks
  • X9Y ISO 05 - X&Y: Reducer on B with reverse flow check
  • Z3P ISO 05: Priority flow control on A with reverse flow check
  • Z3Q ISO 05: Priority flow control on B with reverse flow check
  • Z3T Ninety degree with reverse flow check - reducing
  • Z3V Ninety degree with reverse flow check - reducing
  • Z5D ISO 05 - X&Y: A to T, check T to B
  • Z6U ISO 07: A to T, check T to B
Back to Top
Additional Resources [ + ]
Realces
Technical Tips
Technical Information
Back to Top