Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

跳合, 先导式, 平衡滑阀顺序阀

流量: 7.5 gpm30 L/min. | 插孔: T-163A

全部展开

技术特性 [ + ]

自动跳合顺序阀在进口（口1）压力超过阀设定时全开并保持打开状态，产生从口1到口2（顺序口）的自由油路。口1压力设定与外泄口（口3）相关。只要口1压力超过口2压力，阀就会保持打开状态。欲重新设定此类阀，口1压力必须降至阀的设定值之下，口1至口2的液流必须停止并且口2压力必须等于或大于口1压力。

不能用在负载锁紧应用中。
口3处的压力直接以1:1的比例增加到阀的设定值上，口3处的压力不能超出5000 psi（350 bar）。
如应用在系统的驱动端侧，通过阀的液流必须停止，阀才能回座。如果应用在一个系统的泵端侧，泵必须关闭，阀才能回座。
所有3口顺序阀在尺寸和功能上可互换（如：给定的外形结构尺寸阀拥有相同的流道，相同的插孔）。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-163A
系列	0
通流能力	7.5 gpm30 L/min.
最大操作压力	5000 psi350 bar
工厂默认的设定值	Kick down pointKick down point
110 SUS (24 cSt)下的最大泄漏	2 in³/min.30 cc/min.
额定响应时间	25 ms25 ms
调节 - 从最小设定到最大设定的顺时针圈数	55
阀头部安装六角尺寸	3/4 in.19,1 mm
阀安装扭矩	20 - 25 lbf ft27 - 33 Nm
调节螺栓的内六角尺寸	5/32 in.4 mm
锁紧螺母六角尺寸	9/16 in.15 mm
锁紧螺母力矩	80 - 90 lbf in.9 - 10 Nm
型号重量	.30 lb0,15 kg
Seal kit - Cartridge	Buna: 990163007
Seal kit - Cartridge	Polyurethane: 990163002
Seal kit - Cartridge	Viton: 990163006

回到首页

常见问题 [ + ]

SUN压力控制阀在设置压力时的误差是多少？

设置压力的误差在产品的性能参数页中都有详细说明，您可以通过点击可选产品网页中的更多产品信息到达产品性能参数页面。

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What does Sun mean by the term sequencing?

A sequence valve opens when the pressure at port 1 exceeds the setting of the valve. When pressures at port 1 and port 2 both exceed the setting of the valve the valve goes full open, or sequences. When this happens flow can go in either direction, just so long as port 1 stays above the setting.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

额外来源 [ + ]

集锦

技术指导