Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

防冲击, 先导式, 平衡锥阀顺序阀带口3外泄

流量: 120 gpm480 L/min. | 插孔: T-19A

全部展开

技术特性 [ + ]

先导控制式，防冲击型顺序阀限制最大系统压力，并限制压力上升速度。此类阀的阀口在初始开启之后以恒定速率关小，此速率与设定值及流量无关。调节螺钉决定最大（溢流）设定压力和最小（门限）设定压力。外部泄油口保证阀的设定值与口2压力无关。

当与口3（外泄）压力相关的口1（进口）压力超过阀的设定值而升高时，先导流量随之增加。
口3处的压力直接以1:1的比例增加到阀的设定值上，口3处的压力不能超出5000 psi（350 bar）。
可在口2接受最大压力；适合应用在交叉端口的溢流油路中。
由于调节过程发生在阀的内部，此类阀对大多数与气穴，噪声以及阀块腐蚀有关的问题不敏感。
阀对油液温度的变化和油液污染相对不敏感。
不适用于负载保持的应用场合。
当进口（口1）的压力超出门限设定值，此类阀将开启并接通油箱（口2）。先导部分以恒定的速度向前移动，压缩先导级弹簧并增大阀的设定值。当先导部分移动到机械限位处时，阀达到最大设定值。
主级节流孔被保护并免受污染。
不适用于顺序油缸的应用场合。
压力设定值对口2的背压不敏感。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-19A
系列	4
通流能力	120 gpm480 L/min.
最大操作压力	5000 psi350 bar
工厂默认的设定值	4 gpm15 L/min.
控制先导流量	10 - 25 in³/min.0,16 - 0,41 L/min.
压力上升时间	200 - 400 ms200 - 400 ms
额定响应时间	2 ms2 ms
调节 - 从最小设定到最大设定的顺时针圈数	4.54.5
阀头部安装六角尺寸	1 5/8 in.41,3 mm
阀安装扭矩	350 - 375 lbf ft474 - 508 Nm
调节螺栓的内六角尺寸	5/32 in.4 mm
锁紧螺母六角尺寸	9/16 in.15 mm
锁紧螺母力矩	80 - 90 lbf in.9 - 10 Nm
Seal kit - Cartridge	Buna: 990219007
Seal kit - Cartridge	Viton: 990219006

回到首页

性能曲线 [ + ]

Performance Curve for SDJT: 防冲击, 先导式, 平衡锥阀顺序阀带口3外泄

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What does Sun mean by the term sequencing?

A sequence valve opens when the pressure at port 1 exceeds the setting of the valve. When pressures at port 1 and port 2 both exceed the setting of the valve the valve goes full open, or sequences. When this happens flow can go in either direction, just so long as port 1 stays above the setting.

SUN压力控制阀在设置压力时的误差是多少？

设置压力的误差在产品的性能参数页中都有详细说明，您可以通过点击可选产品网页中的更多产品信息到达产品性能参数页面。

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

额外来源 [ + ]

集锦

技术指导