Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

先导式, 平衡滑阀顺序阀

流量: 30 gpm120 L/min. | 插孔: T-2A

全部展开

技术特性 [ + ]

先导控制式，平衡滑阀结构顺序阀将在进口（口1）压力超过阀的设定之后向次级油路供油。顺序阀的设定将控制与外泄口（口3）压力相关的口1压力。在口2（顺序口）背压升至设定值之前，此类阀对此不敏感。如果回路中有压力存在，它们可以用来代替2口溢流阀完成对压力的调节。

所有3口顺序阀在尺寸和功能上可互换（如：给定的外形结构尺寸阀拥有相同的流道，相同的插孔）。
当与口3（外泄）压力相关的口1（进口）压力超过阀的设定值而升高时，先导流量随之增加。
主级的阻尼孔被150微米的不锈钢滤网保护。
口3处的压力直接以1:1的比例增加到阀的设定值上，口3处的压力不能超出5000 psi（350 bar）。
因为滑阀的泄漏，不适合使用在负载锁紧应用中。
W和Y控制方式是可以指定或不指定特定设定值。当没有特定值设定要求时，将采用标准设定，并全范围可调。当按特定值设定时，这个特定值将会代表阀的最大设定值。
配置EPDM密封圈的插装阀可用在磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-2A
系列	2
通流能力	30 gpm120 L/min.
最大操作压力	5000 psi350 bar
工厂默认的设定值	4 gpm15 L/min.
控制先导流量	10 - 15 in³/min.0,16 - 0,25 L/min.
110 SUS (24 cSt)下的最大泄漏	3 in³/min.@1000 psi50 cc/min.@70 bar
额定响应时间	10 ms10 ms
调节 - 从最小设定到最大设定的顺时针圈数	55
阀头部安装六角尺寸	1 1/8 in.28,6 mm
阀安装扭矩	45 - 50 lbf ft61 - 68 Nm
调节螺栓的内六角尺寸	5/32 in.4 mm
锁紧螺母六角尺寸	9/16 in.15 mm
锁紧螺母力矩	80 - 90 lbf in.9 - 10 Nm
型号重量	.50 lb0,25 kg
Seal kit - Cartridge	Buna: 990202007
Seal kit - Cartridge	EPDM: 990202014
Seal kit - Cartridge	Polyurethane: 990002002
Seal kit - Cartridge	Viton: 990202006

回到首页

性能曲线 [ + ]

Performance Curve for RSFC: 先导式, 平衡滑阀顺序阀

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What does Sun mean by the term sequencing?

A sequence valve opens when the pressure at port 1 exceeds the setting of the valve. When pressures at port 1 and port 2 both exceed the setting of the valve the valve goes full open, or sequences. When this happens flow can go in either direction, just so long as port 1 stays above the setting.

SUN压力控制阀在设置压力时的误差是多少？

设置压力的误差在产品的性能参数页中都有详细说明，您可以通过点击可选产品网页中的更多产品信息到达产品性能参数页面。

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

Related Models [ + ]