RPGS8 | 插装阀 » Pressure Control » 溢流阀

此类阀为带集成先导级控制插孔的常闭调节元件。它为平衡锥阀结构设计。先导级控制插孔可接受任何T-8A插孔的压力控制插装阀。当进口（口1）压力达到先导级控制阀的设定，阀开始向油箱（口2）溢流，节流以调节压力。先导级控制阀的设定决定了口1与口2之间的压力降。

因为调节发生在阀的内部，所以这些阀不会出现与气蚀相关的问题，即噪音和阀块腐蚀。
配置EPDM密封圈的插装阀可用在磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
可在口2接受最大压力；适合应用在交叉端口的溢流油路中。
此阀对变动的油液温度和油液污染不敏感。
主级的阻尼孔被150微米的不锈钢滤网保护。
油箱口（口2）处的背压直接以1:1的比例增加到阀的设定值上。
注意：带-8控制选项，应首先用正确的扭矩安装主级阀。然后用合适的扭矩将T-8A先导级控制阀安装进主级阀中。
-8控制类型允许通过T-8A插孔将先导级控制阀直接旋进溢流阀的顶部。这些先导级控制阀需单独采购并包括电比例，电磁，气控先导，液控先导操作。请参照先导级控制阀。
所有2口溢流阀（除了先导溢流阀）在尺寸和功能上可互换（如：给定的外形结构尺寸阀拥有相同的流道，相同的插孔）。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-3A
系列	2
通流能力	50 gpm200 L/min.
最大操作压力	5000 psi350 bar
控制先导流量	10 - 15 in³/min.0,16 - 0,25 L/min.
先导控制孔型	T-8AT-8A
先导控制阀安装扭矩	20 - 25 lbf ft27 - 33 Nm
先导控制阀安装尺寸	7/8 in.22,2 mm
复位位置时主级泄漏	10 drops/min.0,7 cc/min.
额定响应时间	2 ms2 ms
阀头部安装六角尺寸	1 1/8 in.28,6 mm
阀安装扭矩	45 - 50 lbf ft61 - 68 Nm
型号重量	.50 lb0,25 kg
Seal kit - Cartridge	Buna: 990303007
Seal kit - Cartridge	EPDM: 990303014
Seal kit - Cartridge	Polyurethane: 990303002
Seal kit - Cartridge	Viton: 990303006

回到首页

Performance Curve for RPGS8: 先导式, 平衡锥阀溢流主级带集成T-8A控制插孔

回到首页

Where would I use a kick-down relief?

One graphic example is on a portable grain auger for silos. When the farmer gets caught in the auger the kick-down relief trips and allows him to escape.

SUN压力控制阀在设置压力时的误差是多少？

设置压力的误差在产品的性能参数页中都有详细说明，您可以通过点击可选产品网页中的更多产品信息到达产品性能参数页面。

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Can I use a kick-down relief for my system relief?

Maybe not. We build in a good amount of overlap in the kick-down reliefs to prevent false tripping. This means they are not as fast as our standard pilot operated reliefs. A direct-acting relief valve set just above the kick-down relief valve would be good insurance.

Direct acting, pilot operated, what do I use?

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

How do I get a kick-down relief to reset?

The kick-down relief acts much like a circuit breaker. When the pressure at the inlet (port 1) of the relief valve rises to the setting, the valve pops open and drops the pressure down to 100 psi or so. The valve stays open until flow through it stops. Shutting off the supply of oil will reset the valve; reversing pressure on the valve is a positive way of resetting it.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页