Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

全程可调针阀带反向单向阀

流量: 30 gpm (.38 inch)120 L/min. (9,7 mm) | 插孔: T-16A

全部展开

技术特性 [ + ]

带逆流单向阀的针阀为全调型节流口以用来调节流量。它们可在全闭与最大节流口直径之间无限调节。集成的大流量单向阀提供口2到口1的自由液流。此类阀无压力补偿。

所有的2口流量控制阀在形状上和功能上都可以相互替换（例如对于一个给定结构下的相同的流道，相同的孔型）。但是，阀安装部分的外部尺寸将会相应不同。
由于针阀并不具备压力补偿的结构，固定的小孔将会使流量大小与1口，2口压差的平方根成比例。
平衡的调节结构可以保证在高压力情况下，亦可轻松调节。
锐边小孔的设计可以最大化地减小粘度对于流量变化的影响。
配置EPDM密封圈的插装阀可用在磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
Sun浮动式的结构可以最大限度地减少由于过大的安装扭矩以及孔型加工的误差所造成的干涉现象

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-16A
系列	3
通流能力	30 gpm (.38 inch)120 L/min. (9,7 mm)
最大操作压力	5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏	10 drops/min.0,7 cc/min.
调节 - 从全关到全开的逆时针圈数	55
阀头部安装六角尺寸	1 1/4 in.31,8 mm
阀安装扭矩	150 - 160 lbf ft203 - 217 Nm
调节螺栓的内六角尺寸	5/32 in.4 mm
锁紧螺母六角尺寸	9/16 in.15 mm
锁紧螺母力矩	80 - 90 lbf in.9 - 10 Nm
型号重量	1.30 lb0,60 kg
Seal kit - Cartridge	Buna: 990016007
Seal kit - Cartridge	EPDM: 990016014
Seal kit - Cartridge	Polyurethane: 990016002
Seal kit - Cartridge	Viton: 990016006

回到首页

性能曲线 [ + ]

Performance Curve for NCFB: 全程可调针阀带反向单向阀

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

额外来源 [ + ]

集锦

技术指导