Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

常关, 调节单元

流量: 15 gpm60 L/min. | 插孔: T-11A

全部展开

技术特性 [ + ]

此阀为无内置节流孔的常闭调节单元，用来作为旁路压力补偿器以确保流过节流孔的压降保持恒定，不受进出口压力变化影响。

一个可选的调节（L控制）被提供用来改变通过补偿器的压降，以此来增加或减少流量。
配置EPDM密封圈的插装阀能够用于磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
所有端口都可以接受5000 psi (350 bar)的压力。
耐腐蚀螺纹插装阀是设计用在易腐蚀环境中且阀型号带后缀/AP以用来区分。（参考下面选项）。这些阀的阀体是用高强度双相不锈钢来制造。依据型号，调节螺栓可为钛合金或硅黄铜制造。锁紧螺母，定位丝线和各种控制为316不锈钢制造。内部零件是由与标准阀件相同的碳钢含铅合金制造。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-11A
系列	1
通流能力	15 gpm60 L/min.
最大操作压力	5000 psi350 bar
阀头部安装六角尺寸	7/8 in.22,2 mm
阀安装扭矩	30 - 35 lbf ft41 - 47 Nm
Seal kit - Cartridge	Buna: 990011007
Seal kit - Cartridge	EPDM: 990011014
Seal kit - Cartridge	Polyurethane: 990011002
Seal kit - Cartridge	Viton: 990011006

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

Related Models [ + ]