Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

2通, 先导切换, 双向油路, 比例节流阀带位置切换

流量: 50 gpm200 L/min. | 插孔: T-53AD

全部展开

技术特性 [ + ]

此阀是2位2通比例节流阀.口2、3和口4、5常闭。口1先导压力抵抗弹簧力会在口2、3到口4、5方向上形成一个与口1压力大小成比例的可变节流口。节流口有一定程度的自补偿效果。此阀使用双通道设计。口2、3、4、5结合而形成口2、3和口4、5。一双口可看成单独区域来对待。此阀利用切换活塞来保证阀可靠关闭。

这款阀是工厂定值设定的，并不可以现场设定。任何的篡改都将影响产品保修。
位置的开关都是CE认证的。
当安装该插装阀时，可使用套筒扳手或者类似的装置安装，当遇到位置开关形式的时候，可考虑选用深套筒扳手。
这些阀或许需要通过外部调节逻辑阀提供压力补偿。对并联回路采用LR*C-XHN，或者对于节流回路采用LP*C-XHN。
这款阀提供一定程度的自我补偿，可以用于流量控制。为提高流量控制的精准度，外部的逻辑调节阀可以用来保证大范围流量和压力情况下稳定的流量。可参考附加信息中的曲线。
调节方式可选的保护套，需要单独订货。清查号码：991-043
1口和4口都应限制在500psi（35bar）以内。
口4的作用力相互直接作用于口1。
精确的压力补偿控制要求通过阀的压降保持在一个恒定值。
Sun浮动式的结构可以最大限度地减少由于过大的安装扭矩以及孔型加工的误差所造成的干涉现象

回到首页

切换说明 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

供应电压	20-30 VDC20-30 VDC
运行温度范围	-25 to 80 °C-25 to 80 °C
振动	≥ 50g, 0-500 impulses/sec≥ 50g, 0-500 impulses/sec
冲击	>50 g, 1ms>50 g, 1ms
反极性保护	是是
最大输出负载	≤ 400 mA, Duty Ratio 100%≤ 400 mA, Duty Ratio 100%
短路保护	Yes, Load Short UnlimitedYes, Load Short Unlimited
及时旋转	≤ 25 ms≤ 25 ms
滞环	35 %35 %
热量变化 - 0~80 °C ≤ ±	.004 in.0,1 mm
电磁兼容	DIN EN 61000-6-1/2/3/4DIN EN 61000-6-1/2/3/4
接头	M12 X 1 (4) PinM12 X 1 (4) Pin
接头防护等级	IP65IP65

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-53AD
系列	3
通流能力	50 gpm200 L/min.
最大操作压力	5000 psi350 bar
阀切换需要的先导压力	50 - 120 psi3,5 - 8 bar
完全打开所需要的先导压力	290 - 340 psi20 - 23 bar
110 SUS (24 cSt)下的最大泄漏	10 in³/min.@1000 psi160 cc/min.@70 bar
	.10 in³1,6 cc
阀头部安装六角尺寸	1 1/4 in.31,8 mm
阀安装扭矩	150 - 160 lbf ft203 - 217 Nm
型号重量	4.40 lb2,00 kg
Seal kit - Cartridge	Buna: 990053007
Seal kit - Cartridge	Viton: 990053006

回到首页

性能曲线 [ + ]

Performance Curve for FTFAZ: 2通, 先导切换, 双向油路, 比例节流阀带位置切换

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

Related Models [ + ]