Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

3位4通, 电磁滑阀换向阀, 3000 psi (210 bar) - 通用孔型

流量: 3 gpm11 L/min. | 插孔: SC-08-04

全部展开

技术特性 [ + ]

该3位4通电磁阀为直动式，弹簧对中。当线圈A通电时，流量可从3口（P）流向2口（B），或者从4口（A）流向1口（T）。当线圈B通电时，流量可从3口（P）流向4口（A），或者从2口（B）流向1口（T）。

1口的最大工作压力为290 psi (20 bar)，其他口的最大工作压力为3000 psi (210 bar)。
此阀可被直接驱动且不需要最小液压操作压力。
线圈接头选项提供最高IP67H的防护等级。详见线圈产品页面。
该阀在螺线管上带有一个环形垫片，该垫片应该安装在两个线圈中间以保持线圈在正确的位置。
此阀采用湿式衔铁线圈设计。这意味着衔铁周围的工作流体介质将曝露在线圈所产生热场中。如果线圈长时间通电，这将是一个影响因素。一些液体，特别是水/乙二醇混合物，会在长时间高温下分解并形成凡立水，而这将会影响阀的功能。
线圈可以双向安装到螺线管上。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	SC-08-04
系列	0C
通流能力	3 gpm11 L/min.
最大操作压力	3000 psi210 bar
典型阀泄漏，在110 SUS (24 cSt)	6 in³/min.@3000 psi100 cc/min.@210 bar
额定响应时间	50 ms50 ms
切换频率	15,000 max. cycles/hr15,000 max. cycles/hr
衔铁直径	.51 in..51 in.
阀头部安装六角尺寸	24 mm24 mm
阀安装扭矩	20 - 24 lbf ft27 - 33 Nm
型号重量	.50 lb0,25 kg

回到首页

性能曲线 [ + ]

Performance Curve for DNTC: 3位4通, 电磁滑阀换向阀, 3000 psi (210 bar) - 通用孔型

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting, pilot operated, what do I use?

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

额外来源 [ + ]

集锦