Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

2位4通, 电磁滑阀换向阀带闭式过渡位和位置切换

流量: 8 gpm30 L/min. | 插孔: T-31A

全部展开

技术特性 [ + ]

此类2位4通电磁阀为直动式，平衡滑阀结构。位置间的过渡位是关闭的。关闭的过渡位可大大减少换向时油液的流失。而这方面在先导控制油路中是非常重要的。位置指示开关用来确认阀处在弹簧偏置位置。

线圈必须与此阀一起订购。此阀将在出厂前被设定好，现场不可调。如果是装配需要改变或其它服务，可以将此阀退回到工厂。任何篡改，将违反产品保修条例。
位置指示开关通过CE验证。
当将此阀安装进入它的插孔时，需要使用乌鸦脚扳手或相似的工具，因为位置指示开关使深套筒扳手失去效用。
电磁铁组件的疲劳耐压等级为5000 psi (350 bar)。
阀的通流能力基于将3口作为进油口，1口作为出油口。尽管可以允许反向通流，此时的性能可能会受到影响，因此不推荐这种用法。
此阀可被直接驱动且不需要最小液压操作压力。
此阀采用湿式衔铁线圈设计。这意味着衔铁周围的工作流体介质将曝露在线圈所产生热场中。如果线圈长时间通电，这将是一个影响因素。一些液体，特别是水/乙二醇混合物，会在长时间高温下分解并形成凡立水，而这将会影响阀的功能。
不同的线圈接头与电压选项都是可选的，也同时可选带或不带浪涌保护。
线圈的独特电磁设计使电磁阀有更高的效率，单位瓦特产生高的阀芯驱动力，从而使阀有可靠的切换。
利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。

回到首页

切换说明 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

供应电压	20-30 VDC20-30 VDC
运行温度范围	-25 to 80 °C-25 to 80 °C
振动	≥ 50g, 0-500 impulses/sec≥ 50g, 0-500 impulses/sec
冲击	>50 g, 1ms>50 g, 1ms
反极性保护	是是
最大输出负载	≤ 400 mA, Duty Ratio 100%≤ 400 mA, Duty Ratio 100%
短路保护	Yes, Load Short UnlimitedYes, Load Short Unlimited
及时旋转	≤ 25 ms≤ 25 ms
滞环	≤ .002 in.≤ .002 in.
热量变化 - 0~80 °C ≤ ±	.004 in.0,1 mm
电磁兼容	DIN EN 61000-6-1/2/3/4DIN EN 61000-6-1/2/3/4
接头	M12 X 1 (4) PinM12 X 1 (4) Pin
接头防护等级	IP65IP65

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-31A
系列	1
通流能力	8 gpm30 L/min.
最大操作压力	5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏	10 in³/min.@3000 psi160 cc/min.@210 bar
额定响应时间	50 ms50 ms
切换频率	15,000 max. cycles/hr15,000 max. cycles/hr
衔铁直径	.75 in.19 mm
阀头部安装六角尺寸	7/8 in.22,2 mm
阀安装扭矩	30 - 35 lbf ft41 - 47 Nm
型号重量	.60 lb0,30 kg
Seal kit - Cartridge	Buna: 990431007
Seal kit - Cartridge	Viton: 990431006

回到首页

性能曲线 [ + ]

Performance Curve for DNCAZ: 2位4通, 电磁滑阀换向阀带闭式过渡位和位置切换

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting, pilot operated, what do I use?

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

Related Models [ + ]