Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

24 VDC 线圈带嵌入式比例放大器, 蓝牙, 电压或电流命令

全部展开

技术特性 [ + ]

这种嵌入式的电子放大器是一款紧凑，小巧的线圈/控制器结合的部件，作用于比例电磁阀。放大器可对线圈提供线性控制电流。顶部的LED指示灯将可以很好地表征放大器工作状态。放大器的初始设定只需要下载蓝牙设置APP进行无线连接和设置。这里没有机械设定面板和按钮。一旦设定完成，参数将在记忆单元里永久保存。

LED指示灯显示状态以及输出电流。
匹配最小电流输出，具备短路保护。
5V范围内电位器/手柄控制。
程序使能输入。
所有的输入和输出限制都是单独可调。
单独可调的上升以及下降时间。
微处理控制下更稳定更可靠的性能。
德标DT04-6P接头，等级IP69K。
共地的供电和控制信号，两者相互独立。
可调节的颤振频率，从0到500Hz。Sun推荐的颤振频率为140Hz。
CE认证。
放大器的设置壳通过Sun的 AmpSet Blue™ app无线蓝牙连接设置。
玻璃填充尼龙外壳，内部聚氨酯化合物灌封。
该线圈电磁力分布均匀，可以任意方向安装且不影响性能。
需要与之配套的电缆线，但是不包括在产品中。

回到首页

技术数据 [ + ]

供应电压	18-32V, 24V recommended18-32V, 24V recommended
供应电流	I(sol) + 25mAI(sol) + 25mA
输出电流	600 mA600 mA
颤振频率	Off, 33-500 Hz, in 1 Hz incrementsOff, 33-500 Hz, in 1 Hz increments
斜坡时间	0-65.0 s, 1 ms increments0-65.0 s, 1 ms increments
参考电压	5V (4.6V at 250mA)5V (4.6V at 250mA)
运行温度范围	-4 - 176 °F-20 - 80 °C
模拟输入范围	0-10V, 0-5V, or 0-20mA0-10V, 0-5V, or 0-20mA
模拟输入阻抗	10 Kilo-ohms (Voltage Command Mode), 250 ohms (Current Command Mode)10 Kilo-ohms (Voltage Command Mode), 250 ohms (Current Command Mode)
Card Function	All OptionsAll Options
电压/频率	24 VDC24 VDC
接头	Deutsch DT04-6PDeutsch DT04-6P
型号重量	.50 lb0,25 kg