Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

12 VDC 防风雨线圈带Metri-Pack系列 150-2M接头

全部展开

技术特性 [ + ]

该防风雨线圈用于Sun的全流量电磁和比例阀，在阀暴露在潮湿或者海洋工作环境中时提供良好防护。该阀仅有Metri-Pack系列150-2M接头，五种电压可供选择：12 VDC, 14 VDC, 24 VDC, 28 VDC and 36 VDC。该线圈安装时需要一套额外的防风雨组件，并且插孔需要做进一步适配性加工。请注意：防风雨线圈没有手动超越控制选项。

防风雨线圈仅整套供货，并且不能与插装阀整体供应。
该线圈需要配置额外的防风雨组件。防风雨组件为单独配置，见“适用于”部分。
直流线圈内嵌入瞬态电压抑制二极管。名义击穿电压68V。代码1.5 KE68CA。75℃下稳态电源损耗6.5W，峰值脉冲损耗为1ms时1500W，不可重复。
线圈绕组采用温度等级N, (392° F [200 °C]等级)。
带插头的电源线缆需要单独配置，未包含在产品里面。
防风雨线圈的外径比770标准线圈大4mm。
Metri-Pack, 150-2M系列接头满足温度冲击测试要求，在该测试中，线圈通电并温度稳定后，将其立刻浸入冰水中，重复5次，然后测试线圈隔离电阻，其不应低于10兆欧姆。
为了得到最优的比例性能，应当使用带有电流反馈和可调颤振信号的放大器。颤振频率应当设置为100 - 250 Hz。
IP等级取决于线圈插座类型以及与之相配的插头。
外表为金属材质，采用杜邦77G33L或者工程师批准的等效材料封装，达到防风雨线圈功能。
防风雨线圈达到IP69K防护等级以及1000小时盐雾防护标准。
RoHS认证，限制性材料重量占比低于0.1%。

回到首页

比例性能数据 [ + ]

最大电流	1150 mA1150 mA
122ºF (50ºC)稳定温度下名义线圈电阻	9.4 ±8% ohms9.4 ±8% ohms
Nominal Coil Resistance at 68ºF (20ºC) Cold	6.4 ±8% ohms6.4 ±8% ohms

回到首页

技术数据 [ + ]

在 68ºF (20ºC) 环境温度下，线圈最高温度	218ºF (105ºC)218ºF (105ºC)
电弧消除(TVS)	IncludedIncluded
电量消耗（低温）- 在相关的电压下	22 watts22 watts
最高环境温度	122 °F50 °C
电压/频率	12 VDC12 VDC
运行电压范围	+/- 10% nominal+/- 10% nominal
寿命测试等级	100 %100 %
接头	Metripack Series 150-2MMetripack Series 150-2M
接头防护等级	IP69KIP69K
衔铁直径	.75 in.19 mm
线圈锁紧螺母扭矩	4.5 lbf in.0,5 Nm