Free flow side to nose check valve

Capacity: 30 gpm120 L/min. | Cavity: T-5A
CXED : Free flow side to nose check valve
Technical Features [ + ]

Free-flow, side-to-nose check valves are on/off circuit components that allow free flow from the inlet (port 2) to the outlet (port 1) and block flow in the opposite direction.

  • Two-port check valves share the same cavity for a given frame size, however, pay close attention as flow paths may be in opposite directions.
  • These check valves are considered circuit savers for existing circuits where manifold drillings are incorrect. The capacity of side-to-nose (port 2 to port 1) 2-port check valves is approximately 30% less than preferred models with a nose-to-side (port 1 to port 2) flow path.
  • Check valves offer extremely low leakage rates with a maximum leakage of less than 1 drop per minute (0,07 cc/min).
  • Will accept 5000 psi (350 bar) at ports 1 and 2.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
Back to Top
Technical Data [ + ]
Note: Data may vary by configuration. See CONFIGURATION section.
Cavity T-5A
Series 2
Capacity 30 gpm120 L/min.
Maximum Operating Pressure 5000 psi350 bar
Maximum Valve Leakage at 110 SUS (24 cSt) 1 drops/min.0,07 cc/min.
Valve Hex Size 1 1/8 in.28,6 mm
Valve Installation Torque 45 - 50 lbf ft61 - 68 Nm
Model Weight .40 lb0,20 kg
Seal kit - Cartridge Buna: 990203007
Seal kit - Cartridge Viton: 990203006
Back to Top
Performance Curves [ + ]
Performance Curve for CXED: Free flow side to nose check valve Performance Curve for CXED: Free flow side to nose check valve
Back to Top
FAQs [ + ]
I need to discharge a large accumulator. How can I increase the capacity of my discharge circuit?

Because of the very high ratio, the COFO has limited capacity. The discharge path is across a .050 inch (1,3 mm) diameter orifice. If you have large accumulators combined with low precharge pressures, this may not discharge the energy quickly enough. Using the COFO XDN cartridge in conjunction with an LODA XDN will provide capacity for larger applications.

How big is a drop of hydraulic oil?  

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting or pilot operated - what do I use?

Direct-acting valves are used to prevent over pressure, and pilot-operated valves are used to regulate pressure. If you are unsure, use a direct-acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot-operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What parts of the Sun cartridge valve are field serviceable?
Only external seals are serviceable.  Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.
Back to Top
  • B2A Ninety degree with reverse flow check - reducing
  • B2B Ninety degree with reverse flow check - reducing
  • B2C Ninety degree with reverse flow check - reducing
  • B2D Ninety degree with reverse flow check - reducing
  • B2I Ninety degree with reverse flow check - reducing
  • B2J Ninety degree with reverse flow check - reducing
  • B2K Ninety degree with reverse flow check - reducing
  • B2U Ninety degree with reverse flow check - reducing
  • B2V Ninety degree with reverse flow check - reducing
  • B2W Ninety degree with reverse flow check - reducing
  • B3B Through port 2 with reverse flow check
  • B3C Through port 2 with reverse flow check
  • B3D Through port 2 with reverse flow check
  • B3J Through port 2 with reverse flow check
  • B3K Through port 2 with reverse flow check
  • B3L Through port 2 with reverse flow check
  • B3U Through port 2 with reverse flow check
  • B3V Through port 2 with reverse flow check
  • B3W Through port 2 with reverse flow check
  • B4B Ninety degree with reverse flow check - reducing
  • B4C Ninety degree with reverse flow check - reducing
  • B4D Ninety degree with reverse flow check - reducing
  • B4J Ninety degree with reverse flow check - reducing
  • B4K Ninety degree with reverse flow check - reducing
  • B4L Ninety degree with reverse flow check - reducing
  • B4U Ninety degree with reverse flow check - reducing
  • B4V Ninety degree with reverse flow check - reducing
  • B4W Ninety degree with reverse flow check - reducing
  • B5C Through port 2 with reverse flow check and high capacity port 3
  • B5D Through port 2 with reverse flow check and high capacity port 3
  • B5K Through port 2 with reverse flow check and high capacity port 3
  • B5L Through port 2 with reverse flow check and high capacity port 3
  • B5V Through port 2 with reverse flow check and high capacity port 3
  • B5W Through port 2 with reverse flow check and high capacity port 3
  • BB4 ISO 05: Sequence into A or out of B with reverse flow check
  • BB5 ISO 05: Sequence into B or out of A with reverse flow check
  • BJ4 ISO 05 - X&Y: Sequence into A or out of B with reverse flow check
  • BJ5 ISO 05 - X&Y: Sequence into B or out of A with reverse flow check
  • BMC Cushion lock
  • BMD Cushion lock
  • BMK Cushion lock
  • BML Cushion lock
  • BMV Cushion lock
  • BMW Cushion lock
  • BNC Cushion lock with shuttle
  • BND Cushion lock with shuttle
  • BNK Cushion lock with shuttle
  • BNL Cushion lock with shuttle
  • BNV Cushion lock with shuttle
  • BNW Cushion lock with shuttle
  • BPC Cushion lock with make up checks
  • BPD Cushion lock with make up checks
  • BPK Cushion lock with make up checks
  • BPL Cushion lock with make up checks
  • BPV Cushion lock with make up checks
  • BPW Cushion lock with make up checks
  • BQC Cushion lock with make up checks and shuttle
  • BQD Cushion lock with make up checks and shuttle
  • BQK Cushion lock with make up checks and shuttle
  • BQL Cushion lock with make up checks and shuttle
  • BQV Cushion lock with make up checks and shuttle
  • BQW Cushion lock with make up checks and shuttle
  • N4A Ninety degree with reverse flow check - reducing
  • N4B Ninety degree with reverse flow check - reducing
  • N4C Ninety degree with reverse flow check - reducing
  • N4D Ninety degree with reverse flow check - reducing
  • N4I Ninety degree with reverse flow check - reducing
  • N4J Ninety degree with reverse flow check - reducing
  • N4K Ninety degree with reverse flow check - reducing
  • N4L Ninety degree with reverse flow check - reducing
  • N4T Ninety degree with reverse flow check - reducing
  • N4U Ninety degree with reverse flow check - reducing
  • N4V Ninety degree with reverse flow check - reducing
  • N4W Ninety degree with reverse flow check - reducing
  • W3F Ninety degree with reverse flow check - reducing
  • W3G Ninety degree with reverse flow check - reducing
  • W3H Ninety degree with reverse flow check - reducing
  • WWD Danfoss OMP/OMR: Cushion lock with make up checks and shuttle
  • WWE Danfoss OMP/OMR: Cushion lock with make up checks and shuttle
  • WWF Danfoss OMP/OMR: Cushion lock with make up checks and shuttle
  • WWG Danfoss OMP/OMR: Cushion lock with make up checks and shuttle
  • X9K Danfoss OMS: Cushion lock with make up checks
  • X9N Danfoss OMS: Cushion lock with make up checks
  • X9P Danfoss OMS: Cushion lock with make up checks
  • X9R Danfoss OMS: Cushion lock with make up checks
Back to Top
Additional Resources [ + ]
Highlights
Technical Tips
Technical Information
Back to Top