This valve is a 3-way, normally open modulating element that incorporates an integral pilot control cavity. The pilot control cavity will accept any T-8A pressure control cartridge. The valve reduces a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1, with a full flow relief function from port 1 to tank (port 3). The pilot cartridge's setting determines the difference in pressure between reduced pressure (port 1) and the tank (port 3).

• Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 3000 psi (210 bar).
• Maximum inlet pressure is determined by the bias spring. The D spring is tested with 2000 psi (140 bar) maximum differential pressure and the W spring is tested with 5000 psi (350 bar) maximum inlet pressure.
• NOTE: With the -8 control option, the main stage valve should first be installed to the correct torque value. The T-8A pilot control valve should then be installed into the main stage valve to its required torque value.
• The -8 control option allows the pilot control valve to be incorporated directly into the end of the relief cartridge via the T-8A cavity. These pilot control cartridges are sold separately and include electro-proportional, solenoid, air pilot, and hydraulic pilot operation. See Pilot Control Cartridges.
• Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
• Full reverse flow from reduced pressure (port 1) to inlet (port 2) may cause the main spool to close. If reverse free flow is required in the circuit, consider adding a separate check valve to the circuit.
• Pilot operated valves exhibit very low dead-band transition between reducing and relieving modes.
• Pilot operated valves exhibit exceptionally flat pressure/flow characteristics, are very stable and have low hysteresis.
• All three-port pressure reducing and reducing/relieving cartridges are physically interchangeable (i.e. same flow path, same cavity for a given frame size). When considering mounting configurations, it is sometimes recommended that a full capacity return line (port 3) be used with reducing/relieving cartridges.
• Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

• PP_B-8.dwg
• PP_B-8.dxf

• Compound cartridge (pilot and main stage) assembly information is provided for reference only. Cartridges must be ordered separately and assembled at point of use.
• Stack height value in technical data table includes seal retainer plate.
• Important: Carefully consider the maximum system pressure. The pressure rating of the manifold is dependent on the manifold material, with the port type/size a secondary consideration. Manifolds constructed of aluminum are not rated for pressures higher than 3000 psi (210 bar), regardless of the port type/size specified.

• Sun Offers Zinc-Nickel Plating for Corrosion Resistance
• Válvulas y bobinas a solenoides de la serie Sun FLeX
• Software de configuración CANpoint XMD
• Sun Cartridges with EPDM Seals
• Sun Expands Corrosion-Resistant Solutions
• QuickDesign con SmartConnect Ofrece una Herramienta para Construir Esquemáticos
• Get the relief you need. Adjustable. Ventable. Blockable. FLeX-ible.
• Sun Sandwich Bodies Interchangeable with Bosch and Others
• Electrohidráulica optimizada y ajustada de fábrica desde el primer momento
• Electro-Proportional Basics Explained
• Putting Sun at the heart of hydraulic regenerative braking systems

• Mounting and Assembly of Sandwich Bodies (575.9 KB)
• Proportional Amplifiers and Ancillary Products (2.06 MB)
• Manufacturing Sun Cartridge Cavities (522.27 KB)
• Solenoid Coils for Switching and Proportional Valves (975.2 KB)
• Reducing and Reducing/Relieving Valves (229.15 KB)

• Sun Model Code Explanation; 999-901-334 (343.9 KB)
• Performance Data
• Custom Integrated Packages from Sun
• Cavity Information (S-171) and Tooling
• Electro-Hydraulic Terms and Definitions (2.94 MB)
• QuickDesign & SunDesign: Sun's 3- & 5-Axis Solutions
• Fluid Recommendations: Oil Viscosity, Cleanliness & Temperature
• Cartridges: Materials of Construction
• Sun's Floating Style Screw-In Cartridge (1.06 MB)
• Units of Measure, Settings, and Conversions
• Manifolds: Materials of Construction
• Removing Valves from Ductile Manifolds (73.96 KB)