DLDAZCN224 | Cartridges » Solenoid Operated » 2-way

This solenoid-operated 2-way, 2-position cartridge is a direct-acting, balanced spool directional valve. The valve is available in either a normally open or normally closed configuration.

The position switch provides confirmation that the valve is in the spring biased position. Click Here for the position sensor pin diagram

A coil must be ordered with this cartridge. This cartridge is supplied as a sealed, factory set unit and is not field serviceable. If the assembly requires changes or service it needs to be returned to the factory. Any tampering will violate the product warranty.
Position switch is CE approved.
When torquing this cartridge into its cavity, a crow's foot wrench or similar will be required since the position switch precludes the use of a deep socket wrench.
The solenoid tube assembly is fatigue rated for 5000 psi (350 bar) service.
This valve is direct actuated and requires no minimum hydraulic pressure for operation.
This valve utilizes a wet armature design. This means that the working fluid surrounds the armature and is exposed to the heat generated by the coil. This can be a factor if the coil is energized for long periods of time. Some fluids, notably water/glycol mixtures, break down at these temperatures over time and form varnishes that will affect the function of the cartridge.
A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.
The solenoid's unique magnetic design results in a high efficiency solenoid, yielding high spool actuating force per Watt expended, leading to reliable valve shifting.
Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Back to Top

Note: Data may vary by configuration. See CONFIGURATION section.

Cavity	T-13A
Series	1
Capacity	12 gpm45 L/min.
Maximum Operating Pressure	5000 psi350 bar
Maximum Valve Leakage at 110 SUS (24 cSt)	5 in³/min.@3000 psi80 cc/min.@210 bar
Response Time - Typical	50 ms50 ms
Switching Frequency	15,000 max. cycles/hr15,000 max. cycles/hr
Solenoid Tube Diameter	.75 in.19 mm
Valve Hex Size	7/8 in.22,2 mm
Valve Installation Torque	30 - 35 lbf ft41 - 47 Nm
Model Weight	.50 lb0,25 kg
Seal kit - Cartridge	Buna: 990413007
Seal kit - Cartridge	Viton: 990413006

Back to Top

Note: Data may vary by configuration. See CONFIGURATION section.

Supply Voltage	20-30 VDC20-30 VDC
Operating Temperature Range	-25 to 80 °C-25 to 80 °C
Vibration	≥ 50g, 0-500 impulses/sec≥ 50g, 0-500 impulses/sec
Shock	>50 g, 1ms>50 g, 1ms
Reverse Polarity Protection	YesYes
Maximum Output Load	≤ 400 mA, Duty Ratio 100%≤ 400 mA, Duty Ratio 100%
Short Circuit Protection	Yes, Load Short UnlimitedYes, Load Short Unlimited
Turn On Time	≤ 25 ms≤ 25 ms
Hysteresis	≤ .002 in.≤ .002 in.
Thermal Shift - 0 to 80 °C ≤ ±	.004 in.0,1 mm
EMC	DIN EN 61000-6-1/2/3/4DIN EN 61000-6-1/2/3/4
Connector	M12 X 1 (4) PinM12 X 1 (4) Pin
Connector Environment Rating	IP65IP65

Back to Top

Performance Curve for DLDAZ: 2-way, solenoid-operated directional spool valve with position switch

Back to Top

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Direct acting or pilot operated - what do I use?

Direct-acting valves are used to prevent over pressure, and pilot-operated valves are used to regulate pressure. If you are unsure, use a direct-acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot-operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

Back to Top