Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

12 VDC coil with ISO/DIN 43650, Form A connector

Expand All

Technical Features [ + ]

Coil windings utilize Class N, (392° F [200 °C] rated) magnet wire.
Power cable with mating connector is required and is not included with product.
Encapsulating material: Mineral filled, glass fiber reinforced, epoxy molding compound.
A metal oxide varistor, SIOV-S07K35, for surge suppression is molded directly into the coil to protect the connected electrical circuits from inductive transients.
The coil is magnetically symmetrical and can be mounted in either direction on the solenoid tube without affecting performance.
IP rating is dependent on the coil connector and the mating connector used.
RoHS compliant. Restricted materials less than 0.1% total by weight.

Technical Data [ + ]

Maximum Coil Temperature at 68ºF (20ºC) Ambient	218ºF (105ºC)218ºF (105ºC)
Arc Suppression (TVS)	IncludedIncluded
Power Consumption (cold) - at rated voltage	12 watts12 watts
Voltage/Frequency	12 VDC12 VDC
Operating Voltage Range	+/- 20% nominal+/- 20% nominal
Duty Cycle Rating	100 %100 %
Connector	ISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pinISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pin
Connector Environment Rating	IP65IP65
Solenoid Tube Diameter	.56 in.14,2 mm
Coil Nut Torque	4.5 lbf in.0,5 Nm

Used With [ + ]

What models can this kit be used with?

DAAA
2-way, solenoid-operated directional spool valve - pilot capacity
DACC 2-way, 2-stage, solenoid-operated directional poppet valve
DBAA
3-way, solenoid-operated directional spool valve - pilot capacity

Additional Resources [ + ]

Highlights

Sun's New FLeX Series Solenoid Valves & Coils

Technical Information

Environmental Test Specification for Electrical and Electronic Co (254.61 KB)
Sun's Floating Style Screw-In Cartridge (1.06 MB)
CE Declaration of Conformity - XMD 12-2017 (133.69 KB)

760212 | Accessories » Coils | Sun Hydraulics

Assembly Build Process

Assembly Build Process

12 VDC coil with ISO/DIN 43650, Form A connector

Footer