Baugruppe erstellen

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

Spule 12 VDC, Stecker ISO/DIN 43650 Form A

Alle expandieren

Technische Eigenschaften [ + ]

Spulenwicklungen sind mit Klasse N (200 °C) Spulendraht ausgeführt, um hohe Zuverlässigkeit bei Dauerbetrieb zu garantieren.
Es wird ein Spannungsversorgungskabel mit passendem Stecker benötigt. Das Kabel wird nicht mitgeliefert.
Vergussmasse: Mineralgefülltes, glasfaserverstärktes Epoxyharz.
Ein MOV (Metal Oxide Varistor SIOV-S07K35) ist zum Schutz der Schaltung vor Überspannung mit der Spule vergegossen.
Die magnetische Wirkung der Spule ist symmetrisch. Die Spule kann in beliebiger Ausrichtung, ohne die Funktion zu beeinträchtigen, auf dem Ankerrohr montiert werden.
Die IP Bewertung der Spule hängt von der gewählten Steckverbindung ab.
Blei- und chromfrei gemäß RoHS (Anteil geringer als 0,1 %).

Zurück nach oben

Technische Daten [ + ]

Maximale Temperatur der Spule bei 20 ºC Umgebungstemperatur	105 °C105 °C
Arc Suppression (TVS)	IncludedIncluded
Leistungsaufnahme (kalt) bei Nennspannung	12 Watt12 Watt
Spannung/Frequenz	12 VDC12 VDC
Versorgungsspannungsbereich	+/- 20 % Nennspannung+/- 20 % Nennspannung
Einschaltdauer	100 %100 %
Steckverbinder	ISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pinISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pin
Schutzart des Anschlusses	IP 65IP 65
Ankerrohrdurchmesser	.56 in.14,2 mm
Anzugsdrehmoment der Befestigungsmutter	4.5 lbf in.0,5 Nm