Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

2-vías , acción-directa , balanceado carrete, direccional, operada por solenoide válvula , 3000 psi (210 bar) - common cavity

Capacidad: 6 gpm23 L/min. | Cavidad: SC-10-02

Expand All

Technical Features [ + ]

This solenoid-operated, 2-way, 2-position spool valve is a direct-acting, balanced spool directional valve. The valve is only available in the normally closed configuration.

This valve is designed to be used with the 780 Series coils.

The solenoid tube assembly is fatigue rated for 3000 psi (210 bar) service.
This valve is direct actuated and requires no minimum hydraulic pressure for operation.
All ports are rated to a maximum operating pressure of 3000 psi (210 bar).
This valve features zinc plating on exposed surfaces.
The cartridge installation torque of 22 lbf ft (30 Nm) should be respected for best performance.
Coil connector options offer ratings up to IP69K. See individual coil product pages for details.
The metal coil nut is a functional feature of the valve and should be correctly installed for proper performance of the valve.
This valve utilizes a wet armature design. This means that the working fluid surrounds the armature and is exposed to the heat generated by the coil. This can be a factor if the coil is energized for long periods of time. Some fluids, notably water/glycol mixtures, break down at these temperatures over time and form varnishes that will affect the function of the cartridge.
Coils can be mounted on the tube in either direction.

Technical Data [ + ]

Notar: Los datos pueden variar según la configuración . Consulte la sección de CONFIGURATION

cavidad	SC-10-02
Series	1C
Capacity	6 gpm23 L/min.
Maximum Operating Pressure	3000 psi210 bar
Typical Valve Leakage at 110 SUS (24 cSt) Inlet on 1	9.5 in³/min.@3000 psi9.5 in³/min.@3000 psi
Typical Valve Leakage at 110 SUS (24cSt) Inlet on 2	2 in³/min.@3000 psi30 cc/min.@210 bar
Response Time - Typical	50 ms50 ms
Switching Frequency	15,000 max. cycles/hr15,000 max. cycles/hr
Solenoid Tube Diameter	.50 in.12,7 mm
Valve Hex Size	25 mm25 mm
Coil Nut Torque	3.5 - 3.9 lbf ft4,8 - 5,3 Nm
Valve Installation Torque	21 - 23 lbf ft28 - 31 Nm
Model Weight	.30 lb0,15 kg

Performance Curves [ + ]

Performance Curve for DLUT: 2-vías , acción-directa , balanceado carrete, direccional, operada por solenoide válvula , 3000 psi (210 bar) - common cavity

FAQs [ + ]

Direct acting or pilot operated - what do I use?

Direct-acting valves are used to prevent over pressure, and pilot-operated valves are used to regulate pressure. If you are unsure, use a direct-acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot-operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

Additional Resources [ + ]

Realces

Technical Tips

Solenoid Operated Directional Valves (1.01 MB)
Manufacturing Sun Cartridge Cavities (522.27 KB)
Solenoid Coils for Switching and Proportional Valves (975.2 KB)

Technical Information

Coil Information [ + ]

No coil selected.

DLUTXCN

X-Control, C-Spool

Configuration Rules

DLUT | Cartuchos » Solenoid Operated » 2-vías | Sun Hydraulics

Assembly Build Process

Assembly Build Process

2-vías , acción-directa , balanceado carrete, direccional, operada por solenoide válvula , 3000 psi (210 bar) - common cavity

Footer