Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

24 VDC bobina con infrarrojo integrado función de aumento gradual

Expand All

Technical Features [ + ]

The Embedded Electronics Amplifier is a compact, low profile coil/controller combination for use with proportional solenoid valves. The Amplifier provides current to the coil in proportion to a specified time constant. Bright LED indicators on the unit provide an overview of the operating status. Setup is accomplished through Sun's Amplifier Set Up Software or the Hand Held Programmer (HHP). There is no cover to remove and no tiny pots to set. Once configured, the settings are stored in permanent memory within the unit. With power applied, the ramping amplifier outputs the specified minimum current. Applying a voltage (minimum 9 V) to the command pin initiates the specified ramp up in current. Removing the command signal initiates the ramp down in current.

Easily configured using Sun's Amplifier Set Up Software or the Hand Held Programmer.
LED indication of Status and Output Current
Selectable dither frequency up to 300 Hz including OFF. Sun's recommended dither frequency is 140 Hz.
Adjustable current limited output with short circuit protection
Adjustable ramp up and ramp down times, independently set
Microprocessor controlled for consistent, reliable performance
Deutsch DT04-6P Connector, IP69K rated
Glass filled nylon enclosure with Lexan light pipes and polyurethane potting compound
Power cable with mating connector is required and is not included with product.
CE approved - See CE Testing Results and Explanation, document number 999-991-260, for details

Technical Data [ + ]

Supply Voltage	Equals coil voltage within +/-10%Equals coil voltage within +/-10%
Supply Current	I(sol) + 20mAI(sol) + 20mA
Output Current	600 mA600 mA
Dither Frequency	Off, 80-300 Hz, in 20 Hz incrementsOff, 80-300 Hz, in 20 Hz increments
Ramp Time	0-120.0 s, 0.5 s increments0-120.0 s, 0.5 s increments
Operating Temperature Range	-20 to 70 °C-20 to 70 °C
Analog Input Range	Digital Signal 9-28 VDigital Signal 9-28 V
Analog Input Impedance	13 Kilo-ohms13 Kilo-ohms
Card Function	Ramp Only OptionRamp Only Option
Voltage/Frequency	24 VDC24 VDC
conector	Deutsch DT04-6PDeutsch DT04-6P

Used With [ + ]

What models can this kit be used with?

FMDA Electro-proporcional 3-vías control de caudal válvula , alimentación regulada
FMDB Electro-proporcional 3-vías control de caudal válvula , alimentación regulada
FPCC Electro-proporcional control de caudal válvula - normalmente cerrado
FPCH Electro-proporcional control de caudal válvula - normalmente abierto
FPFK Pilot-operated, normalmente cerrado, electro-proporcional estrangulación con anti-retorno de caudal inverso
FPHK Pilot-operated, normalmente cerrado, electro-proporcional estrangulación con anti-retorno de caudal inverso
PRDL
Electro-proporcional , acción-directa , reductor/alivio de presión válvula con transición abierta
PRDM Electro-proporcional , acción-directa , reductor/alivio de presión válvula con transición abierta - ajuste a alta presión sin comando
PRDN Electro-proporcional , acción-directa , reductor/alivio de presión válvula , ajuste a alta presión sin comando
PRDP
Electro-proporcional , acción-directa , reductor/alivio de presión válvula
PSDL Electro-proporcional , acción-directa , reductor/alivio de presión válvula con transición abierta y drenaje al puerto 4
PSDP Electro-proporcional , acción-directa , reductor/alivio de presión válvula con drenaje al puerto 4
RBAN Electro-proporcional alivio válvula - capacidad de pilotaje, ajuste a alta presión sin comando
RBAP Electro-proporcional alivio válvula - capacidad de pilotaje
991700
Programador portátil
991702 Infrarrojo adaptador
991704 USB infrarrojo adaptador
991706003 Deutsch DT06-6S ensamblaje
991706006 Deutsch DT06-6S ensamblaje