Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

24 VDC bobina con ISO/DIN 43650, Form A conector without TVS Diode - 19mm, common cavity

Expand All

Technical Features [ + ]

Power cable with mating connector is required and is not included with product.
IP rating for this coil is IP65.
This coil does not include a transient voltage suppression (TVS) diode and should only be used when surge suppression is included elsewhere in the electrical system.
Coil windings utilize Class H, (365° F [185 °C] rated) magnet wire.
The coil is magnetically symmetrical and can be mounted in either direction on the solenoid tube without affecting performance.

Technical Data [ + ]

Operating Temperature Range	-4 to 215 °F-4 to 215 °F
Arc Suppression (TVS)	NoneNone
Power Consumption (cold) - at rated voltage	24 Watts24 Watts
Maximum Ambient Temperature	104 °F40 °C
Voltage/Frequency	24 VDC24 VDC
Operating Voltage Range	+/- 10% nominal+/- 10% nominal
Duty Cycle Rating	100 %100 %
conector	ISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pinISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pin
Solenoid Tube Diameter	.75 in.19 mm
Coil Nut Torque	44 lbf in.44 lbf in.
Model Weight	.62 lb.62 lb

Proportional Performance Data [ + ]

Resistance at 20º C	24.0 ohms ±10%24.0 ohms ±10%
Maximum Current (100% Duty Cycle at Maximum Ambient Temperature)	600 mA600 mA

Used With [ + ]

What models can this kit be used with?

DNUC 4-vías, 3-posiciones, direccional, operada por solenoide carrete válvula , 3600 psi (250 bar) - common cavity

Additional Resources [ + ]

Realces

Válvulas y bobinas a solenoides de la serie Sun FLeX

Technical Information

Sun's Floating Style Screw-In Cartridge (1.06 MB)
Environmental Test Specification for Electrical and Electronic Co (254.61 KB)
CE Declaration of Conformity - XMD 12-2017 (133.69 KB)

779224 | Accesorios » Bobinas | Sun Hydraulics

Assembly Build Process

Assembly Build Process

24 VDC bobina con ISO/DIN 43650, Form A conector without TVS Diode - 19mm, common cavity

Footer