Baugruppe erstellen

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

2/2-Wege, 先导切换, Doppelanschluss, proportional Drossel

Durchfluss: 15 gpm60 L/min. | Einschraubbohrung: T-52AD

Alle expandieren

Technische Eigenschaften [ + ]

Technische Daten [ + ]

Leistungskurven [ + ]

FAQs [ + ]

Vergleichbare Modelle [ + ]

Passendes Zubehör [ + ]

Info [ + ]

Zusätzliche Hilfsmittel [ + ]

FTCAXCN

view all

Konfiguration ändern Regeln

Einschraubbohrung	T-52AD
Serie	2
Durchfluss	15 gpm60 L/min.
Zulässiger Betriebsdruck	5000 psi350 bar
Pilot Pressure Required to Shift Valve	60 - 130 psi4 - 9 bar
Aufsteueröldruck zur vollen Ventilöffnung bei Nenndurchfluss	290 - 340 psi20 - 23 bar
Maximale Ventilleckage bei 24 cSt	5 in³/min.@1000 psi80 cc/min.@70 bar
Verdrängungsvolumen des Steuerkolbens	.05 in³0,82 cc
Einstellbereich: Anzahl Umdrehungen im Gegenuhrzeigersinn von geschlossen bis offen	55
Hysterese	35 %35 %
Schlüsselweite des Ventilsechskants	1 1/8 in.28,6 mm
Anzugsdrehmoment des Einschraubventils	45 - 50 lbf ft61 - 68 Nm
Schlüsselweite des Innensechskants der Verstellung	5/32" in.4 mm
Schlüsselweite der Kontermutter	9/16 in.15 mm
Anzugsmoment der Kontermutter	80 - 90 lbf in.9 - 10 Nm
Gewicht	1.00 lb0,45 kg
Seal kit - Cartridge	Buna: 990152007
Seal kit - Cartridge	Viton: 990152006

FTCA | Einschraubventile » Flow Control » Proportionaldrosseln | Sun Hydraulics

Baugruppe erstellen

Baugruppe erstellen

LoadMatch™ ROI Calculator

2/2-Wege, 先导切换, Doppelanschluss, proportional Drossel

Symbols for FTCA

Symbols for FTCA

Footer